Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Tampa?
Gate parts and welding in Tampa typically run $150 to $1,200, with most single-repair jobs landing between $275 and $550. A simple hinge re-weld or a replacement roller set sits near the low end. A racked steel frame that needs cutting out, squaring, and re-welding a new box section runs toward the top. A failed control board or actuator swap on an electric gate can push past $900 once the part and labor are tallied.
We’re Kingston Gate Repair, and gates are the only thing we work on. Manual or automatic, swing or slide, residential or commercial – our technicians arrive already knowing your operator. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so whether you’re staring down a Mighty Mule DIY install gone crooked or a DoorKing access-control operator at a warehouse gate, the diagnosis is faster and the fix is usually done in a single visit.
Key Takeaways
- Most Tampa gate welding and parts jobs cost $275 – $550.
- Hinge and frame re-welds are the most common request we get.
- Salt air and summer humidity along the bay drive rust and part failure faster here than inland.
- A stuck gate rarely needs a full replacement – diagnosing the part first saves hundreds.
- Free estimates: call (877) 752-3303.
Gate Parts & Welding Cost Breakdown (2026)
Here’s what the work actually costs in the Tampa market this year. Ranges are for parts plus labor on a standard residential gate unless noted.
| Job | Typical Cost Range |
|---|---|
| Hinge re-weld (per hinge) | $150 – $275 |
| Gate frame crack or seam weld | $225 – $450 |
| Racked frame repair (cut, square, re-weld) | $400 – $850 |
| Welding a new box section or brace into a steel gate | $350 – $700 |
| Hinge replacement (weld-on, heavy-duty) | $250 – $500 per pair |
| Roller / guide wheel replacement (slide gate) | $150 – $325 |
| Gate latch, striker, and stop hardware | $125 – $300 |
| Control board replacement | $350 – $750 |
| Actuator / operator arm replacement | $450 – $1,100 |
| Safety loop or photo-eye replacement | $275 – $600 |
| Intercom / keypad integration repair | $250 – $650 |
| Commercial gate service (heavy-duty operator) | $600 – $1,800+ |
What pushes a job up? Rust damage here is the big one. Tampa’s salt air and wet-season humidity eat through mild steel and lower-grade hinges, so what looks like a loose gate is often a rusted-through weld that needs more than a quick bead. Frame repairs also cost more when the gate is racked – meaning the frame has dropped out of square – because we have to cut out the damaged section, true the geometry, and weld it back with a brace that actually holds. On the parts side, brand and cycle rating drive price. A Ghost Controls board for a residential driveway gate costs far less than a DoorKing control board in a high-cycle commercial operator. Commercial gates built for dozens of cycles an hour need heavier actuators, and those parts carry heavier price tags.
If your gate needs welding or a part we don’t carry, we’ll tell you up front before we start. Our full Gate Parts & Welding in Tampa service covers the whole job from the control board to the hinge.
What Affects Gate Parts & Welding Pricing in Tampa
No two gates fail the same way, and the price tag follows the failure. Here’s what moves the number in Tampa specifically.
- Rust and corrosion. Properties near the bay, the river, and the Gulf-facing neighborhoods deal with salt-laden air year-round. Steel hinges and lower-grade gate hardware rust from the inside out, so a job that starts as a re-weld can turn into a replacement once we open it up. A gate kept within a few blocks of Tampa Bay often needs heavier hardware than the same gate inland.
- Gate material. Aluminum is lighter and won’t rust but can crack at stress points; steel welds cleanly but rusts; wrought-style and mixed-material gates take more careful prep time. The welding process and rod differ by metal, and that’s labor.
- Frame condition (racked vs. sound). A gate that’s dropped out of square, or shopped at the latch corner, needs geometry work on top of the weld. That adds time and usually a new brace.
- Electric vs. manual. An electric gate adds operator, control board, safety-loop, and intercom costs that a manual gate doesn’t have. A manual gate that just needs a hinge re-weld is one of the cheapest jobs we do.
- Brand and cycle rating. We work across nine operators, from entry-level Mighty Mule and Ghost Controls up to commercial-grade FAAC, BFT, and DoorKing. Parts for a consumer swing-gate opener cost a fraction of a high-cycle commercial operator.
- Permit and access. Some larger repairs or replacements near property lines touch local electrical and building review; gated communities and commercial lots can also add access-scheduling time. We’ll flag it before work starts.
How to Save on Gate Parts & Welding
You don’t need to replace a gate that just needs a weld. That’s the single biggest way to save – a $400 frame repair beats a $3,500 replacement every time, and most gates we see are repairable. A few practical moves:
- Fix the small stuff before it spreads. A rusted hinge caught early is a $150 re-weld. Left alone, it drags the whole frame out of square and turns into an $800 job.
- Wash the salt off. A quick rinse of hinges and hardware a couple times a month during the wet season slows corrosion. It sounds basic, and it works.
- Get a diagnosis before ordering parts. Guessing wrong on a control board is an expensive lesson. We diagnose first, then quote the part – we’re brand-agnostic, so we have no reason to steer you toward an unnecessary replacement.
- Bundle the visit. If we’re already out for a weld, it’s cheaper to add a latch or roller replacement on the same visit than to book two.
- Ask for a free estimate. We’ll price the repair and tell you honestly if a replacement is the better math. Call (877) 752-3303.
FAQs – Gate Parts & Welding Cost
How much does gate welding cost in Tampa?
Gate welding in Tampa runs $150 to $850, with most single repairs around $275 to $550. A hinge re-weld lands near the low end; a racked frame that needs cutting and re-welding a new section runs higher. Call (877) 752-3303 for a free, exact quote on your gate.
Is it cheaper to repair or replace a gate in Tampa?
Repair is almost always cheaper – a weld or part fix in the $150 to $700 range versus a full replacement that runs several thousand. We only recommend replacement when the frame has rusted through in multiple spots or the operator is beyond parts support. We’ll give you the honest call either way.
How much does an electric gate control board cost in Tampa?
A control board replacement typically costs $350 to $750 installed, depending on brand. A residential Ghost Controls or Linear board sits at the lower end; a DoorKing or FAAC commercial board runs higher. Call (877) 752-3303 and we’ll quote your exact operator.
Do you weld aluminum and steel gates?
Yes – we weld both, plus mixed-material gates, and the price depends on the metal. Steel frame repairs run $225 to $450; aluminum and wrought-style work can cost a bit more in prep time. Mention your gate material when you call (877) 752-3303.
Can you fix my gate the same day in Tampa?
Often, yes – most hinge, roller, and latch jobs we handle in a single visit because our trucks carry common parts. Control board and actuator swaps depend on the brand and part availability. Call (877) 752-3303 early and we’ll tell you what’s realistic for your gate.
Why do gates rust faster in Tampa?
Salt air and summer humidity along the bay and river neighborhoods speed up corrosion, especially on mild-steel hinges and lower-grade hardware. That’s why weld and hinge jobs are so common here – and why catching rust early saves real money. Call (877) 752-3303 for a free assessment.
Get a Straight Answer on Your Gate
If your gate is sagging, sticking, or won’t latch, we’ll diagnose it and tell you what the repair costs before we touch a tool. From the control board to the hinge, manual or automatic, swing or slide, we work on your brand – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, or Mighty Mule. Call (877) 752-3303 for a free estimate, or start from our home page to see the full scope of what we handle.
Pricing reflects the Tampa market as of 2026. Kingston Gate Repair offers free estimates – call (877) 752-3303.
What Our Customers Say
"The loop detector under the driveway had failed and residents were stuck holding the button. He traced it, found the break, and had the exit loop reading cars again the same visit."
— Maya Rao"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
— Carrie Sullivan"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
— Rosa Garcia